BGP

news

MTP Pro connector Conversion Kit Guide

Using MTP ®/ When MPO optical fiber jumper is wired, its polarity and male and female head are factors that need special attention, because once the wrong polarity or male and female head is selected, the optical fiber network will not be able to realize communication connection. So choose the right MTP ®/ MPO optical fiber patch cord is an arduous and challenging task for network administrators, because at present, some users often choose the wrong polarity and male and female head, which will increase the purchase cost of additional products and even lead to project delay. In order to solve this problem, the industry has developed MTP ® Pro fiber optic jumper and MTP ® Pro connector conversion toolbox, so that users can quickly and more MTP on site ® Polarity and male and female head of Pro optical fiber jumper. This article will introduce this solution in detail.

3.8 (1)

What is the MTP ® pro connector conversion kit?

MTP ® Pro connector conversion kit can easily change MTP ® Polarity and male and female head of Pro optical fiber jumper. Using MTP ® When the pro connector conversion kit is used, the MTP can be converted within one minute without removing the connector shell or peeling off the jumper ® Changing the polarity and male and female heads of Pro optical fiber jumpers is easy for untrained technicians.

What’s in the MTP ® pro connector conversion kit?

MTP ® Pro conversion tool: MTP ® The “polarity” port and “pin” port of Pro conversion tool are used to change polarity and male and female heads. The “polarity” port (located on the left in the picture) is mainly used to change the polarity of the connector; The “pin” port (located on the right side of the picture) is mainly used to change the male and female heads for fixation.

Green clamp: this clamp can only be used when changing the male and female heads of the connector. It is mainly used to take out the pins in the connector or install the pins.

Needle guide exchanger: mainly used to replace MTP ® The pin of Pro connector, so as to change the male and female head.

Cleaning pen: mainly used to clean MTP ® The end face of Pro connector can be used for more than 500 times.

MTP ® All of the above components are essential for the polarity and male and female head of the MTP pro optical fiber jumper.

How to use MTP ® Pro connector conversion kit changes MTP ® polarity of the pro fiber jumper?

MTP ® The pro polarity / male / female head conversion tool can change the MTP ® The position of the key on the MTP pro optical fiber jumper connector to realize polarity conversion. The MTP of polarity A is shown below ®- 12 MTP ® Take Pro trunk fiber jumper as an example to illustrate how to use MTP ® The pro connector conversion kit changes polarity.

3.8 (2)

Step 1: MTP ® Remove the clamp on the pro conversion tool, and then remove the MTP of polarity a ®- 12 MTP ® One end connector (key up) of the pro backbone optical fiber jumper is placed on the MTP ® In the “polarity” port of Pro conversion tool;

Step 2: until the connector is inserted into the “polarity” port, the sound of “click” is heard;

Step 3: take out the MTP of polarity a ®- 12 MTP ® Connector for pro backbone fiber patch cord.

Step 4: observe MTP ®- 12 MTP ® The key of MTP Pro backbone optical fiber jumper connector can be found to change, and the key up and key down exchange positions, that is, MTP of a polarity ®- 12 MTP ® The pro backbone fiber patch cord is successfully converted to MTP of polarity B ®- 12 MTP ® Pro backbone fiber patch cord.

Vice versa, if you want to change the MTP of polarity B ®- 12 MTP ® The conversion of the pro backbone fiber jumper to polarity a can be realized according to the above operation.

How to use MTP ® Pro connector conversion kit changes MTP ® male and female head of Pro optical fiber jumper?

Via MTP ® The pro polarity / male female head conversion tool changes the pin on the connector to realize MTP ®- 12 MTP ® Conversion of male and female heads of Pro backbone optical fiber jumper.

3.8 (3)

1.Male to female

Step 1: MTP ® Remove the clamp from the pro conversion tool and then remove the MTP ®- 12 MTP ® Plug the male (with pin) connector of the pro backbone optical fiber jumper into the MTP ® In the “pin” port of Pro conversion tool, you will hear the sound of “click”;

Step 2: remove the blue pin without pin from MTP ® Insert the other side of the pro conversion tool into the “pin” port and align with it;

Step 3: press MTP ® While pro conversion tool, clamp the blue pin with clamp (green);

Step 4: pull out the blue pin and remove the MTP ®- 12 MTP ® MTP can be found by observing the connector of Pro backbone optical fiber jumper ®- 12 MTP ® The pin on the connector of the pro backbone optical fiber jumper was taken out, and the male head was successfully converted into the female head.

2.Female to male

Step 1: MTP ® Remove the clamp from the pro conversion tool and then remove the MTP ®- 12 MTP ® Insert the female connector of the pro backbone fiber jumper into the MTP ® In the “pin” port of Pro conversion tool, you will hear the sound of “click”;

Step 2: remove the Yellow pin with pin from MTP ® Insert the other side of the pro conversion tool into the “pin” port and align with it;

Step 3: after inserting, gently press the Yellow pin, and then pull out the Yellow pin;

Step 4: remove MTP ®- 12 MTP ® MTP can be found in the connector of Pro backbone optical fiber jumper ®- 12 MTP ® The pin was successfully inserted into the female connector of the pro backbone optical fiber jumper, and the female connector was successfully converted into a male connector.


Post time: Mar-08-2022